ATI DB005I-006 ProCharger 6 Rib Blower Belt

ATI DB005I-006  ProCharger 6 Rib Blower Belt

These belts are currently only offered to those who know the ProCharger part number from their current belt. Please put the part number in the "notes" section of the order form.

Systems that use standard series pulleys
P1SC, P1SC-1, P1SC-2, D1, D1SC, F-1D, F1, F1-A, F1-C, F1-R Superchargers

LS1 F-BODY 6 RIB BELT / PULLEY MATRIX

Matrix for 5.82" ( 6" ) crank pulley

CRANK PULLEY              BLOWER PULLEY             BELT

DC017A-006                DP300I-06D                  DB355I-006

DC017A-006                DP310I-06D                  DB355I-006

DC017A-006                DP320I-06D                  DB355I-006

DC017A-006                DP340I-06D                  DB355I-006

DC017A-006                DP350I-06D                  DB365I-006

DC017A-006                DP360I-06D                  DB365I-006

DC017A-006                DP370I-06D                  DB365I-006

DC017A-006                DP385I-06D                  DB370I-006

DC017A-006                DP400I-06D                  DB370I-006

DC017A-006                DP410I-06D                  DB370I-006

DC017A-006                DP425I-06D                  DB374I-006

DC017A-006                DP438I-06D                  DB374I-006

DC017A-006                DP450I-06D                  DB374I-006

DC017A-006                DP463I-06D                  DB380I-006

DC017A-006                DP475I-06D                  DB380I-006

Replacement Idler: DC003A-061 2.3" idler with bearings

2.3" idler with bearings

Idler shaft: DM008A-002

Pulley spacer PDW01C-075 .075" D series impeller shim

Remove the driver's upper and the lower stand to

bracket mounting bolts and loosen the passenger upper

bolt to allow bracket to be pivoted enough for the belt to

be installed over the lower standoff. Hang the belt on

the standoff and install and tighten all stand to bracket

bolts.

Some belts will be easier to install if you pivot the

supercharger in the bracket using the lower mounting

bolt only. Install the belt over the crank pulley and then

finish installing the blower mounting bolts. The antisway

bar may need to be lowered to facillitate

installation of some of the mounting bolts.

.075" D series impeller shim

Remove the driver's upper and the lower stand to

bracket mounting bolts and loosen the passenger upper

bolt to allow bracket to be pivoted enough for the belt to

be installed over the lower standoff. Hang the belt on

the standoff and install and tighten all stand to bracket

bolts.

Some belts will be easier to install if you pivot the

supercharger in the bracket using the lower mounting

bolt only. Install the belt over the crank pulley and then

finish installing the blower mounting bolts. The antisway

bar may need to be lowered to facillitate

installation of some of the mounting bolts.

 

 

LS1 F-BODY 8 RIB BELT / PULLEY MATRIX

Matrix for 7.65" crank pulley DC017A-008

ATI Dampner #918853

CRANK PULLEY         BLOWER             PULLEY BELT

DC017A-008            DP340I-08D      DB392I-008

DC017A-008            DP355I-08D      DB392I-008

DC017A-008            DP370I-08D      DB400I-008

DC017A-008            DP385I-08D      DB400I-008

DC017A-008            DP390I-08D      DB400I-008

DC017A-008            DP400I-08D      DB400I-008

DC017A-008            DP413I-08D      DB408I-008

DC017A-008            DP425I-08D      DB408I-008

DC017A-008            DP438I-08D      DB415I-008

DC017A-008            DP450I-08D      DB415I-008

DC017A-008            DP463I-08D      DB415I-008

DC017A-008            DP475I-08D      DB415I-008

DC017A-008            DP500I-08D      DB415I-008

DC017A-008            DP525I-08D      DB427I-008

Replacement Idler: DC004A-082 2.7" idler with bearing

2.7" idler with bearing

Idler shaft: DM008A-003

Blower pulley spacer PDW01C-100 .100" D series impeller shim

.100" D series impeller shim

Install notes

Remove the driver's upper and the lower stand to bracket mounting bolts

and loosen the passenger upper bolt to allow bracket to be pivoted enough

for the belt to be installed over the lower standoff. Hang the belt on the

standoff and install and tighten all stand to bracket bolts.

Some belts will be easier to install if you pivot the supercharger in the

bracket using the lower mounting bolt only. Install the belt over the crank

pulley and then finish installing the blower mounting bolts. The anti-sway

bar may need to be lowered to facilitate installation of some of the

mounting bolts.

The ProCharger crank pulley should be installed on the ATI dampner in the

following manner: remove the 3 5/16" FerryCap bolts on the ATI dampner

retaining the A/C pulley. Rotate the A/C pulley so the 3/8"-16 holes line up

with the 3/8"-16 holes of the dampner. Install the 3) 4" long 3/8"-16 all

threaded stainless bolts with lock and thick washers in the corresponding

holes through the ProCharger crankpulley, ATI dampner and A/C pulley

making sure to hold the A/C pulley tight against the dampner during

installation. Anti-seize should be used on these bolts. This installation

process is necessary as ATI recently changed the configuration of the FBody

dampner which removed the dedicated drive bolt holes.

 

 

Find what belt size you need here for your C5!

 

* Old Bracket, with Fixed Idlers (either size) factory tensioner*

4.75" Pulley = 97.0"
4.50" Pulley = 97.0"
4.37" Pulley = 96.6"
4.10" Pulley = 96.6"
3.85" Pulley = 96.0"


* Old Bracket, with Gates Tensioner attached*

4.50" Pulley = 99.7"
4.375" Pulley = 99.7"
4.10" Pulley = 99.4"
3.85" Pulley = 98.8"


* Stage II Brackets*

5.00" Pulley = 90.8"
4.75" Pulley = 90.5"
4.63" Pulley = 90.5"
4.50" Pulley = 90.0"
4.38" Pulley = 90.0"
4.25" Pulley = 90.0"
4.10" Pulley = 89.5"
4.00" Pulley = 89.5"
3.85" Pulley = 88.8"
3.70" Pulley = 88.8"
3.60" Pulley = 88.8"
3.50" Pulley = 88.8"
3.40" Pulley = 88.8"
3.20" Pulley = 88.8"
3.10" Pulley = 88.8"
3.00" Pulley = 88.8"

C5 BELT / PULLEY MATRIX STAGE II

Impeller speed @ 6500 ENGINE RPM

6500 ENGINE RPM

6-Rib D-series Crank dia Belt Impeller RPM - LS6

3.00 7.37 KO60888 65470

3.10 7.37 KO60888 63358

3.20 7.37 KO60888 61378

3.40 7.37 KO60888 57768

3.50 7.37 KO60888 56117

3.60 7.37 KO60888 54558

3.70 7.37 KO60888 53084

3.85 7.37 KO60888 51016

4.00 7.37 KO60895 49103

4.10 7.37 KO60895 47905

4.25 7.37 KO60900 46214

4.38 7.37 KO60900 44843

4.50 7.37 KO60900 43647

4.63 7.37 KO60905 42421

4.75 7.37 KO60905 41350

5.00 7.37 KO60908 39282

Impeller speed @ 6200 ENGINE RPM

6200 ENGINE RPM

6-Rib D-series Crank dia Belt Impeller RPM - LS1

3.00 7.37 KO60888 62448

3.10 7.37 KO60888 60434

3.20 7.37 KO60888 58545

3.40 7.37 KO60888 55102

3.50 7.37 KO60888 53527

3.60 7.37 KO60888 52040

3.70 7.37 KO60888 50634

3.85 7.37 KO60888 48661

4.00 7.37 KO60895 46836

4.10 7.37 KO60895 45694

4.25 7.37 KO60900 44081

4.38 7.37 KO60900 42773

4.50 7.37 KO60900 41632

4.63 7.37 KO60905 40463

4.75 7.37 KO60905 39441

5.00 7.37 KO60908 37469

 

ATI DB005I-006 ProCharger 6 Rib Blower Belt
Click To Enlarge
  • Item #: ATI DB005I-006
  • Manufacturer: ATI ProCharger (Accessible Technologies Inc)
  • Condition: New
  * Marked fields are required.
Qty*
Price $59.20

Related Items

Reviews (0) Write a Review
No Reviews. Write a Review