Brute Speed's Formula with ProCharger Featured in GM High-Tech

http://www.youtube.com/watch?v=abZ1zqwggVg&feature=youtu.be

Video of this Formula in action!

1995 Pontiac Firebird Formula Front
 
 
 
1995 Pontiac Firebird Formula Front

1995 Pontiac Firebird Formula - Stock - But Not A Rock

A Blown, Stock LT1 Pushes Jon Beam's Formula Into The 10s
From the November, 2010 issue of GM High-Tech Performance
By Barry Kluczyk
Photography by Barry Kluczyk
1995 Pontiac Firebird Formula Front
Let's be honest, running 10.9s these days in a street car isn't quite the headline material it was a few years ago. It's quick, no question about it-but it's been done. Jon Beam's Firebird Formula, however, is a member of the 10-second club without an LS motor and the usual mods like a big cam and spray. In fact, his '95 Formula still sports a stock LT1 engine under the hood, albeit with an ATI ProCharger blowing into it. That's right, stock. No cam, no heads, not even forged internals. The same cast crank, rods, and pistons that were originally slipped into the Gen II small-block (with two-bolt mains) 15 years ago. They've stood up to the centrifugal blower's 9 pounds of boost admirably well.
1995 Pontiac Firebird Formula Interior
Years later, Beam and his brother Bob operated Exotic Performance Plus, a speed/tuning shop in the Muncie area. That provided the impetus, facility, and opportunity to take the Firebird not just to the next level, but a whole new realm of performance. Sure, there's a ProCharger P-1SC hung on the front of the engine, but it has taken more than 357 horsepower and 343 lb-ft of torque at wheels (on a stingy Mustang dyno) to deliver a 10-second timeslip. "The power is useless unless you can get it to the ground effectively and efficiently," he says. To that end, Beam tossed the factory 10-bolt rear axle and replaced it with a Moser 12-bolt, including 4.30 gears and a lightweight aluminum spool. There's also a full complement of suspension components, including a Spohn torque arm, control arms, and 25mm sway bar along with a BMR Panhard bar and subframe connectors. Air Lift drag bags and QA1 single-adjustable shocks work with the stock springs in the rear. Up front is a BMR tubular K-member and control arms. QA1 double-adjustable shocks and 300-pound springs, as well as Art Morrison travel limiters, comprise the front suspension. The suspension setup is continually tuned and adjusted to optimize launch bite. "You have to experiment to find the right balance for perfect launches," says Beam. "The car has been very consistent and launches hard and straight."
1995 Pontiac Firebird Formula Wheel
Now, as for that stock-bottomed LT1, it's true that Beam has never gazed at the rotating assembly inside it, but he's done the necessary work to match the P-1SC blower and its fuel requirements. That meant adding a 52mm throttle body and 50-pound injectors from Holley, which are fed by an Aeromotive A1000 fuel pump and regulator. The only modification to the stock heads are a stiffer set of dual-coil valvesprings from Crane Cams under the valve covers, which raised the seat pressure to about 125 pounds, along with a set of Comp Cams Magnum 1.6:1 ratio roller-tip rockers to add valve lift and because the stock rockers wouldn't work with the dual-coil springs. And just to be clear, everything in the block is original, including the smallish camshaft, which has 0.449/0.460-inch lift, 202/208 degrees of duration, and a pretty wide 117-degree lobe separation angle-not exactly a dream cam for a blower engine. Stock heads and bottom end also mean a stock 10.4:1 compression ratio, too, which is pretty high for a blower. So careful tuning was a must to prevent turning the original hypereutectic pistons into mush. Beam turned to Ed Wright to reprogram the factory controller. There's also an LT4 knock module implanted in the PCM to prevent the ever-common false knock.
1995 Pontiac Firebird Formula Tires
Additional engine and underhood details include an ATI damper, MSD two-step launch control (Beam takes off at 4,000 rpm), and SJM alternator relocation kit that moves the alternator to the bottom of the engine, enabling the removal of the power steering pump and air-conditioning paraphernalia. That's good for a significant weight savings of about 50 pounds. This car also uses a lightweight Flaming River manual steering rack. Inside, the Formula is mostly stock looking, but obviously outfitted for the track with a Kirkey aluminum driver seat (the stock passenger and rear seat are still in place), RCI five-point harness, Grant steering wheel (saving the weight of the factory airbag module), dash-mounted Auto Meter tach, and a Wolfe six-point rollbar. Beam also moved the battery to the cargo hatch.
1995 Pontiac Firebird Formula Gauge
If you look carefully at the specs for this fast Firebird, you'll notice there's nothing exotic in its assembly, but it is running 10s with less than 400 rear-wheel horsepower and a stock LT1. That's not a fluke. Beam is a fastidious competitor who tunes the chassis and suspension to launch effectively. He regularly snags sub-1.5-second 60-foot times with the hard-hooking Pontiac. Minimizing mass is another key to quick e.t.'s and Beam has baselined everything in the car to judge how new parts and other changes affect the race weight, which is currently at about 3,450 pounds. "Every little bit counts," he says. "And you have to be careful, because some important parts intended to support greater performance ultimately weigh more than the stock parts you took off. I found that out with the tubular K-member. For a manual steering setup, it is two pounds heavier than power steering-but it still substantially lighter overall than the stock K-member."
1995 Pontiac Firebird Formula Interior
1995 Pontiac Firebird Formula Rear
1995 Pontiac Firebird Formula Gauge
1995 Pontiac Firebird Formula Wires
1995 Pontiac Firebird Formula Tanks
1995 Pontiac Firebird Formula Wheel
1995 Pontiac Firebird Formula Tires

1995 Pontiac Firebird Formula - Stock - But Not A Rock

1995 Pontiac Firebird Formula Rear
Data File
Car: 1995 Pontiac Firebird Formula
Owner: Jon Beam
Block: LT1, 350 cid
Compression ratio: 10.4:1
Heads: Stock LT1, 1.94 intake, 1.50 exhaust valves
Cam: Stock hydraulic roller, 0.449/0.460-inch lift, 202/208 duration at 0.050, 116LSA
Pushrods: Stock
Rocker arms: Comp Cams Magnum 1.6 ratio
Pistons: Stock, hypereutectic
Rings: Stock
Crankshaft: Stock, cast iron
Rods: Stock, powdered metal
Throttle body: Holley 52mm
Fuel injectors: Holley 50 lb/hr
Fuel pump: Aeromotive A1000 pump and regulator
Ignition: Stock Opti, MSD coil, wires, 6AL
Engine management: Stock, tuned by Ed Wright/Fastchip
Power-adder: ATI ProCharger P-1SC
Boost: 9 psi
Intercooler: ProCharger twin air-to-air
Exhaust system: Hooker 1.75-inch long-tube headers, Mufflex Y-pipe, Hooker cat-back
Transmission: TH400, built by Rossler Transmissions
Torque converter: Neil Chance 9.5-inch, 4000-stall
Driveshaft: Mark Williams 3.5-inch aluminum
Front suspension: BMR K-member, control arms, QA1 coilovers, Art Morrison travel limiters
Rear suspension: Stock springs, Spohn torque arm, lower control arms, sway bar, BMR Panhard bar, Air Lift drag bags, QA1 shocks
Rearend: Moser 12-bolt, 4.30 gear, 33-spline axles, spool
Brakes: Strange front, Wilwood rear
Wheels: Weld Pro Star 15x3.5 front, 15x10 rear
Front tires: MT ET Front 26x7.5
Rear tires: MT ET Street 28x12.5, drag radial 275/60R15
Fuel octane: 93 (with Torco Accelerator)
Race weight: 3,450 pounds
Best ET/mph: 10.91/121.9
Best 60-ft. time: 1.452
Current mileage: 5,662
1995 Pontiac Firebird Formula Wires 1995 Pontiac Firebird Formula Gauge 1995 Pontiac Firebird Formula Tanks
Brute Speed's Formula Featured in GM High-Tech
Click To Enlarge
  • Item #: Brute Speed Formula
  • Manufacturer: ATI ProCharger (Accessible Technologies Inc)
  • Condition: New
  * Marked fields are required.
Qty*
Price $25,000.00

Related Items

Reviews (0) Write a Review
No Reviews. Write a Review