BMR SBP010 05-10 Mustang/07-10 Shelby GT500 Sway Bar Package

BMR SBP010 05-10 Mustang/07-10 Shelby GT500 Sway Bar Package

BMR SBP010 05-10 Mustang/07-10 Shelby GT500 Sway Bar Package

BMR SBP010 05-10 Mustang/07-10 Shelby GT500 Sway Bar Package

FREE SHIPPING!

The two primary functions of sway bars are to control body roll and to determine the understeer or oversteer behavior of a vehicle. Stock sway bars have low torsional spring rates because they are manufactured from small diameter bar stock or tubing. BMR Suspension’s SBP010 sway bar package was designed by factoring in the vehicle weight, application, motion ratio, coil spring rate, and adjustability requirements. The package consists of BMR’s SB022 front sway bar and SB023 rear sway bar. 
 
 
 SB022
 BMR Suspension’s SB022 front sway bar is manufactured from heavy-wall 35mm DOM tubing, the SB022 is cold formed to better resist torsional fatigue and retain its "memory" far longer than the hot-formed bars used by many competitors. The sway bar is CNC-formed for exact manufacturing tolerances and repeatable high quality. Thrust washers are welded to the bar to locate the sway bar bushing mounts. This is critical as it properly locates the sway bar and prevents lateral movement during hard cornering maneuvers. The sway bar mounts to the car using polyurethane bushings. These bushings are molded from 88-durometer, low-deflection, polyurethane, and are internally fluted to keeps grease in the bushing. The steel sway bar mounting brackets are reinforced to minimize deflection. The sway bar is 3-way adjustable to tune the amount of torsional spring rate and to determine the handling characteristics (understeer/oversteer) of the vehicle.
 
 BMR Suspension designed the SB022 sway bar for street performance, autocross, and road race applications. The large adjustable sway bar’s three positions give you the versatility to drive to and from the road course or autocross and still out handle the competition with the same sway bar. The rate increases and adjustability allow you to fine-tune the handling characteristics of your Mustang so you can drive harder through corners with minimal body roll. The hollow design allows for loads of strength in the lightest package possible. This means increased performance with no sacrifices. The SB022 attaches to your Mustang with 88-durometer polyurethane bushings, reducing the deflection from the stock rubber bushings. This allows for more sway bar control, and more control equals better handling. When performance is a must, rely on BMR Suspension!
 
 
 SB023
 BMR Suspension’s SB023 rear sway bar is manufactured from heavy-duty 22mm bar stock, the SB023 is cold formed to better resist torsional fatigue and retain its "memory" far longer than the hot-formed bars used by many competitors. The sway bar is CNC-formed for exact manufacturing tolerances and repeatable high quality. The SB023 attaches to your Mustang with billet aluminum end links and 88-durometer polyurethane bushings, reducing the deflection from the stock rubber bushings. These bushings are molded from 88-durometer, low-deflection, polyurethane, and are internally fluted to keep grease in the bushing. The CNC-machined, billet aluminum sway bar end links eliminate deflection. 
 
 BMR Suspension designed the SB023 sway bar for street performance, autocross, and road race applications. The non-adjustable SB023 gives you a 52% increase in rate over the stock bar (depending on year and model). The rate increases gives you improved handling characteristics so you can drive harder through corners with minimal body roll. This allows for more sway bar control, which equals better handling. When performance is a must, rely on BMR Suspension!
 
 NOTE: BMR SB023 rear sway bar is not compatible with convertible models unless the additional OE convertible bracing is removed.
 
 Saves $20 when you purchase the package!
 
 BMR Suspension’s SBP006 sway bars are available in black hammertone and red powdercoat for long-lasting good looks. Installation time is about 3-4 hours. Proudly made in the U.S.A.!

SB022
- Fits 2005-2010 S197 Mustangs
- Designed for street performance, autocross, and road race applications
- Dramatically reduces body roll
- Cold formed to better resist torsional fatigue
- Manufactured from 38mm heavy-wall DOM tubing for increased strength
- Five-way adjustable for street and track use 
- Adjustability allows for fine-tuning of suspension
- 88-durometer, greasable polyurethane bushings
- Zinc-plated inner sleeves
- Durable powdercoat finish
- 1-hour installation time
- Proudly designed in the U.S.A.
- Proudly made in the U.S.A.


SB023
- Fits 2005-2010 S197 Mustangs
- Designed for street performance, autocross, and road race applications
- Dramatically reduces body roll
- 52% increase is sway bar rate over stock sway bar (depending on year and model)
- Cold formed to better resist torsional fatigue
- Manufactured from 22mm heavy-duty bar stock for increased strength
- Non-adjustable design
- CNC-machined billet aluminum sway bar end links
- 88-durometer, greasable polyurethane bushings
- Zinc-plated inner sleeves
- Durable powdercoat finish
- 1-2-hour installation time
- Proudly designed in the U.S.A.
- Proudly made in the U.S.A.

 

Package Part Numbers:

SBP010H

SBP010R

 

Product Name:

Sway bar package

 

Product Description:

This kit consists of the following parts:

BMR-SB022

BMR-SB023


SBP010H

Sway bar package

Application: 2005-2010 Mustang

Application: 2007-2010 Shelby GT500

Box Dimensions (SB022H): 56” x 17” x 5”

Shipping Weight (SB022H): 19 pounds

Box Dimensions (SB023H): 66” x 14” x 5”

Shipping Weight (SB023H): 20 pounds

Department: Chassis & Suspension

Section: Suspension Components

Part Type: Sway Bars

Brand: BMR Suspension

Position: Front and Rear

Front Sway Bar Type: Hollow

Rear Sway Bar Type: Solid

Front Sway Bar Diameter (in): 1.375"

Front Sway Bar Diameter (mm): 35.0 mm

Rear Sway Bar Diameter (in): 0.875"

Rear Sway Bar Diameter (mm): 22.0 mm

Mounting Hardware Included: Yes

Sway Bar Finish: Black hammertone powdercoated

Sway Bar Material: Steel

Quantity: Sold individually

 

SBP006R

Sway bar package

Application: 2005-2010 Mustang

Application: 2007-2010 Shelby GT500

Box Dimensions (SB022R): 56” x 17” x 5”

Shipping Weight (SB022R): 19 pounds

Box Dimensions (SB023R): 66” x 14” x 5”

Shipping Weight (SB023R): 20 pounds

Department: Chassis & Suspension

Section: Suspension Components

Part Type: Sway Bars

Brand: BMR Suspension

Position: Front and Rear

Front Sway Bar Type: Hollow

Rear Sway Bar Type: Solid

Front Sway Bar Diameter (in): 1.375"

Front Sway Bar Diameter (mm): 35.0 mm

Rear Sway Bar Diameter (in): 0.875"

Rear Sway Bar Diameter (mm): 22.0 mm

Mounting Hardware Included: Yes

Sway Bar Finish: Red powdercoated

Sway Bar Material: Steel

Quantity: Sold individually

 


The Finer Details

Part Number: BMR SBP010

Manufacturer: BMR Suspension

Condition: New

Weight: 60 lbs


$0.00
$609.00
Earn0
reward points



BMR SBP010 05-10 Mustang/07-10 Shelby GT500 Sway Bar Package

Send this to a friend

BMR SBP010 05-10 Mustang/07-10 Shelby GT500 Sway Bar Package