BMR SP033 2" Lowering Springs for 1964-1966 A-Body

BMR Suspension 2” Lowering Springs for 1964-1966 A-Body

The SP033R product has been redesigned. The bottom coil of the rear spring has been altered to better allow the spring to sit on the rear axle housing. The spring rate and the drop distance remain the same.

There is nothing like the aggressive look of a car with the right stance! Over time, stock springs sag, get rusty, and simply wear out. BMR Suspension believes the right springs go beyond looks—your GM A-body needs to perform, too! All BMR springs are manufactured from chrome silicon high-tensile spring wire, and are cold wound on a CNC coiling machine. The CNC coiling head can adjust the spring diameter in real time to ensure that every spring is exactly the same. This guarantees that your right spring matches your left spring. Every BMR spring is compressed solid at the factory, not once, but twice. This gives the spring its permanent set, and guarantees no sag. BMR springs are stress-relieved at 750 degrees F, ensuring most stresses induced during the winding process are eliminated. All springs are then shot-peened to eliminate residual surface stresses. Many spring manufacturers skip this step, but BMR insists on this operation as part of our spring manufacturing process. Every spring is computer tested as the last step—every spring, not just a sample from each batch. Each spring is loaded in the spring tester at the factory, then compressed and the CNC load cell measures the force for a variety of spring lengths. This allows BMR to offer a LIFETIME WARRANTY against spring sag.
 
 Blending aesthetics and performance, BMR has designed the SP033 for the street performance crowd who want to use their cars in a variety of application. These springs will drop the front end of your 1964-1966 GM A-body 2-inch, and feature a fine-tuned spring rate to give you great handling and a smooth ride. The spring rate offers plenty of support, keeping the body flat and level in the corners, while remaining soft enough for a comfortable ride on any road. When performance and looks are a must, rely on BMR Suspension!
 
 BMR Suspension’s SP033 lowering springs are available in red powdercoat for long-lasting good looks. Installation time is about 2-3 hours. Proudly made in the U.S.A.

Improve the stance and handling capabilities of your A-Body with a set of Lowering Springs from BMR Suspension.  The front springs lower the vehicle by 2” and have a linear spring rate of 520 pounds per inch.  The rear springs also lower the vehicle by 2” and have a variable spring rate of 125-200 pounds per inch.  All BMR springs are cold wound from high tensile silicone chromium spring wire then shot-peened and computer tested for consistency.  A set of BMR Lowering Springs (SP033) will lower the center of gravity and dramatically increase the cornering capabilities of your A-Body without sacrificing ride quality.  Front springs and rear springs also sold separately. Installation time of 3-4 hours.  Available in red powdercoat finish.

- Lowers the front of your 1964-1966 GM A-body 2-inch
- Improves handling and ride quality
- Manufactured from chrome silicon high-tensile spring wire
- Cold wound on a CNC Coiling Machine to exact specifications
- Lifetime warranty against spring sag
- Stress-relieved at 750 degrees F
- Shot-peened
- Computer tested for accurate height and spring rate
- Made in the U.S.A.

Description (SP033):

Lowering the center of gravity not only provides visual appeal, it also dramatically improves the handling ability of your A-Body. BMR lowering springs are specifically designed to provide optimal handling without sacrificing ride quality. Our extensive development time produced what we feel to be the optimal rates for this application. By using a linear 520 lb/in front spring and a variable rate 125-200 lb/in rear spring the car responds with a firm yet comfortable ride with much improved handling characteristics.  These springs will lower you’re A-body by approximately 2” in the front and 2” in the rear.

All BMR springs are cold wound from high-tensile chrome silicon wire, stress relieved, compressed for permanent set then shot peened and computer tested. Some of these procedures are overkill but it ensures a long, trouble-free life with consistent rates and ride heights. Because of these features, BMR is able to offer a lifetime warranty against spring sag.

SP033

Description : Lowering spring kit, set of 4, 2" drop

Application : 1964-1966 Buick Gran Sport, Skylark, Sportwagon

Application : 1964-1966 Chevy Chevelle, Malibu, El Camino, Monte Carlo

Application : 1964-1966 Oldsmobile 442, Cutlass, Vista Cruiser

Application : 1964-1966 Pontiac GTO, LeMans, Tempest

Box Dimensions : 14" x 12” x 12”

Shipping Weight : 38 pounds

Department : Chassis & Suspension

Section : Suspension Components

Part Type : Lowering Springs

Brand : BMR Suspension

Spring Position : Front and Rear

Spring Type : Coil

Progressive Rate Spring, Front : No

Spring Rate, Front (lbs/in) : 521 lbs/in

Drop, Front : 2"

Progressive Rate Spring, Rear : Yes

Spring Rate, Rear (lbs/in) : 200 lbs/in

Drop, Rear : 2"

Bushings Included : No

Spring Finish : Red powdercoated

Quantity : Sold as a set of 4